Sold by KAWELL and Fulfilled by Amazon. Used & new (1) from $9.99 KAWELL® Universal 2 lead LED Light Bar Wiring Harness Kit with Fuse Relay ON / OFF Switch for LED Offroad Driving light LED lamp fog light work light ( 12V 40A waterproof )DetailsKawell K5-5118 18W 6.2-Inch. DC 9-32V 6500K 1170LM 90 Degree Waterproof LED light bar for ATV, Jeep… 100 x 2 x 2 inches 4.0 out of 5 stars #9,015 in Automotive (See top 100) #51 in Automotive > Replacement Parts > Lighting & Electrical > Electrical > Wiring Harnesses 8 ounces (View shipping rates and policies) KAWELL® - Let Hi-tech Light up Your Way. KAWELL universal wiring harness kits is designed for LED Offroad Driving light LED lamp fog light work light and up to 20" LED light bar. Universal Fitment: Compatible with all vehicles or boats that use a 10-30v DC power source. Basically any car battery will work on this wire harness. Just connect your lights to your batter and flip the switch. 6.5 ft wiring ( from relay to lights 6.2 ft , from switch to relay 9.2 ft) The length of this wire harnesses will allow you to mount your LED lights to nearly anywhere you want.

Just run the harness from the battery to your desired lighting location. Other features: 1, High quality 40 amp power relay. 2, 30A blade fuse, max rated at 30A. 3, Illuminated on/off switch with 3M tape. 5, Easily connects any lighting accessory to its power source by taping into the battery directly. 6, LED lights are expensive and in all cases should be protected against melt / fire / smoke or burn out. 7, IP67 waterproofing rating. Complete Wiring Kit Includes: 1, Wiring harness 2, 40A power relay 3, 30A blade fuse 4, ON/OFF switch with 3M tape (On/Off) 5, Instruction Available in: Dual light harness - mounts up to two lights. If you need Heavy Duty wiring harness for up to 300W light bar, please kindly visit our KAWELL Store to select. See all 156 customer reviews See all 156 customer reviews (newest first) I've a cub cadet zero turn lawn mower and it's beginning to get dark earlier in the day, and on a few occasions I've been out post sunset and have had a hard time seeing what I...

I bought this wiring harness expecting two leads... Just like the description says. I got done feeding the switch through the firewall, attached all the ground and "hot"... looks like it should just the ticket Cheap switch and poor craftsmanship on this product....it would have been cheaper and better to just buy the parts separately. This harness makes it fast to hook up any off-road lights. Glad I won't have to make anymore harnesses in the future. The relay pigtail harness is wrong from the factory.86 and 85 are backwards.chandelier restaurant skokie ilThe one on the right is the Kawellvisual comfort large george ii chandelier the button does not workturquoise chandelier earrings siman tu

Switch looks terrible, the relay caught fire while installing. (Just glad it was while i was installing so i knew what was happening and not while... See and discover other items: trailer wiring harness kit Pop Colors vs. Neutral Colors Our latest addition of standard plug-in pendant lights pose the question of do I go with a pop color? Or do I go neutral? We styled one living room four different ways, and the results might surprise you... lamp rewiring kit, containing socket, cord and plug Before starting, make sure lamp is not plugged in. Use the screwdriver to press the sleeve of the socket out. If the socket has a "press here" inscription, press your thumb on the inscription and lift the sleeve off. Pull the socket up and use the wire cutter to cut/disconnect the old wires. Flip lamp over and unscrew nut on bottom of lamp base. Pull thread up and remove old socket. Pull the cord out of the bottom of the fixture. Feed the new cord from the lamp kit through the hole in the bottom of the lamp until it comes out at the top, and attach new socket.

Using the wire cutters, split wires by cutting along the groove. Use the wire cutter to remove approximately an inch of the insulation from each wire. Tie the split cords using an underwriter's knot. Make a loop with each wire and then feed the opposite color wire through each loop to create a figure eight. Note: Check the lamp kit's instructions for an illustration. Use the screwdriver to loosen the screws on either side of the new socket. Wrap each exposed wire around a screw on the socket. Use the screwdriver to tighten the screws and hold the wires in place. Slide the sleeve back on the socket until it snaps into place. Test the wire by plugging it into an outlet.A Connecticut Based Life + Style Blog Read previous post:My Vintage, Beach WeddingI've mentioned here on the blog before that my style has done a 180 since our marriage almost 3 years... I'm replacing the wiring from a vintage chandelier and need to know what gauge wire to use. There are five lights on it.

This is for the fixture only! 18g stranded wire is quite common on arms 14g stranded is often used to join the 18g arm strands, and to tie into the ceiling. This applies to North America and normal chandeliers with relatively low (<50 each) wattage bulbs. If you're in the US, NEC likely applies. Article 402 covers fixture wires, and explains what types and sizes are allowed. Table 402.3 lists the types of wires allowed to be used as fixture wires. If you're going to rewire the fixture, you'll have to use a type of wire listed in this table. KF-1, KF-2, KFF-1, KFF-2 RFH-1, RFH-2, RFHH-2, RFHH-3 SF-1, SF-2, SFF-1, SFF-2 Table 402.5 lists the allowable ampacity for different sizes of wire. You'll want to use a wire that's sized properly for the load you'll be serving. In most cases, the maximum bulb size you'll have to account for is 100 Watt. Which means you'll likely only be looking at about 833 mA (100 Watts/120 Volts), so you can probably get away with 18 AWG wire.

402.6 says that fixture wires cannot be smaller than 18 AWG, so you'll have to use at least that size wire. 402.12 points to 240.5 for overcurrent protection of fixture wires, which tells you what size overcurrent is required for different sized wires. 240.5(B)(2) lists the size and length of fixture wires, when connected to circuits with various sizes of overcurrent protection. National Electrical Code 2014 Article 240 Overcurrent Protection 240.5 Protection of Flexible Cords, Flexible Cables, and Fixture Wires. (B) Branch-Circuit Overcurrent Device.Fixture wire shall be permitted to be tapped to the branch-circuit conductor of a branch circuit in accordance with the following: (1) 20-ampere circuits — 18 AWG, up to 15 m (50 ft) of run length (2) 20-ampere circuits — 16 AWG, up to 30 m (100 ft) of run length (3) 20-ampere circuits — 14 AWG and larger (4) 30-ampere circuits — 14 AWG and larger (5) 40-ampere circuits — 12 AWG and larger